| information du capteur |
| Sensor |
|
| Mono/Color |
|
| Sensor type |
|
| Shutter type |
- Rolling shutter
- Global reset shutter
|
| Résolution |
|
| Pixel size |
|
| Exposure time |
|
|
| Dark noise |
|
| Saturation capacity |
|
| Dynamic range |
|
| Signal-to-noise ratio |
|
| Quantum efficiency |
- 60,1 % @ 465 nm
- 67,1 % @ 535 nm
- 49,8 % @ 630 nm
|
| formats d'acquisition |
| Image formats, interface frame rate max. |
- Full Frame, 5472 × 3648 px, max. 6 fps
- Binning 2×2, 2736 × 1824 px, max. 9 fps
- Binning 2×1, 2736 × 3648 px, max. 9 fps
- Binning 1×2, 5472 × 1824 px, max. 9 fps
|
| Image formats, aquisition frame rate max. (Burst Mode) |
- Full Frame, 5472 × 3648 px, max. 9 fps
|
| Pixel formats |
- BayerRG8
- BayerRG10
- BayerRG12
- BayerRG12 Packed
- Mono8
- Mono10
- Mono12
- Mono12 Packed
- RGB8
- BGR8
|
|
| Analog controls |
- Gain (0 … 20 dB)
- Offset (0 … 255 LSB 12 Bit)
|
| Color models |
|
| Color processing |
- Integrated color processor for high quality color calculation
|
| caractéristiques de l'appareil |
| Basic Functions |
- Exposure
- Gain / Color Gain
- Trigger / Exposure Active (Flash)
- Binning 2x2
- Partial Scan
- Offset
- Free Running Mode (Live Image)
|
| Auto Functions |
- Exposure Auto
- Gain Auto
- White Balance Auto
- Color Transformation Auto
|
| Image Pre-processing |
- Color Processing (RGB, BGR, Mono)
- Color Enhancement (with optimized ColorTransformationMatrix)
- LUT / Gamma
|
| Acquisition / Interface |
- Burst Mode
- Adjustable Framerate
- Device Link Throughput Limit
- Internal Image Buffer
|
| Synchronisation |
|
| Trigger sources |
- Hardware
- Software
- ActionCommand
|
| Trigger delay |
- 0 … 2 s, tracking and buffering of up to 256 trigger signals
|
| Process Synchronization |
- Events
- Timer
- Trigger Delay
- Debouncer
- Counter
- Trigger via Action CMD (GigE)
- Additional Output Modes (e.g. Trigger Ready)
- PWM (PWM Duration / PWM Duty Cycle)
- 4 power outputs with up to 120 W (max. 48 V / 2.5 A)
- Selectable Output format (e.g. Tri State, Push Pull)
- Chunk data inside transferred image
- Encoder support via Counter End trigger source
|
| Additional Functions |
- User Set
- Integrated temperature sensor
- Readable additional information (e.g. sensor information)
|
| Calibration data |
- Integrated color correction matrix (3000 K, 5000 K, 6500 K, 9500 K, and user defined)
- Camera calibration data (user defined storage for intrinsic / extrinsic camera parameters, and geometry distortion values)
- Customer data storage (128 bytes user defined)
|
| Internal image buffer |
- 58 MB
- 1 image (Trigger Mode)
- 1 image (Free Running Mode)
|
| Interfaces et connecteurs |
| Data interface |
- Gigabit Ethernet, Transfer rate 1000 Mbits/sec, Fast Ethernet, Transfer rate 100 Mbits/sec, Connector: M12 / 8 pol x-coded, screwable type
|
| Process interface |
- M12 / 12 pins a-coded (SACC-CI-M12MS-12CON-L180)
|
| Power supply |
- via M12/12 pins a-coded or Power over Ethernet (PoE)
|
| Données mécaniques |
| Lens mount |
|
| Width |
|
| Height |
|
| Profondeur |
|
| Poids |
|
| Matériau |
|
| Données électriques |
| Plage de tension +Vs |
- 12 … 24 V DC (external power supply)
- 36 … 57 V DC (Power over Ethernet)
|
| Puissance absorbée |
- Approx. 3.2 W @ 12 VDC and 9 fps
- Approx. 3.8 W @ 48 VDC (PoE) and 9 fps
|
|
| Flash memory size |
|
| Conditions ambiantes |
| Operating temperature |
- 0 … +65 ° @ T = measurement point
|
| Température en magasin |
|
| Humidity |
- 10 … 90 % (non-condensing)
|
| Classe de protection |
- IP 40 (with mounted lens and cable)
- IP 54 (with mounted lens and cable)
- IP 65 (with mounted tube and cable)
- IP 67 (with mounted tube and cable)
- IP 69K (with stainless steel housing accessory)
|
| E/S numériques |
| Lines |
- 4 input lines
- 4 power output lines with pulse width modulation (PWM) (max. 48 V / max. 2,5 A)
|
| Output line sources |
- Off
- Exposure Active
- Timer1
- Readout Active
- User0
- User1
- User2
- TriggerReady
|
| Conformité |
| Conformity |
|
